Kubota KX71-3S Hydraulic Final Drive Motor

N:16mm; Weight:0.92 kg; J:117 mm; A:31 mm; C0:11.2 kN; Designation of housing:FL206N-; B:38.1 mm; T min.:-40 °C; L:80 mm; s1:19.05 mm;

C1 - Dynamic Radial Rating (1 million revolutions)6:147000 lbf; Cone Part Number:HM535349; C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)1:256000 lbf; G1 - Heat Generation Factor (Roller-Raceway):750; db - Cone Backface Backing Diameter:7.56 in; C0 - Static Radial Rating:265000 lbf; B -

da - Cone Frontface Backing Diameter:7.68 in; db - Cone Backface Backing Diameter:7.68 in; C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)4:258000 lbf; G1 - Heat Generation Factor (Roller-Raceway)8:692; Design Units:Imperial; C0 - Static Radial Rating:242000 lbf; G2 - Heat Generation Fac

Inner ring reference:No; C:9 mm; Characteristic outer ring frequency, BPF0:4.53 Hz; Characteristic rolling element frequency, BSF:5.49 Hz; Lubrication hole on outer ring:Non/No; Nlim (grease):23,000 rpm; Fw:7 mm; Min operating temperature, Tmin:-20 °C; C0r:2.93 kN; Cr:3.15 kN;

A5:25.4 mm; L:274 mm; T min.:-20 °C; s1:21.45 mm; B:42.9 mm; C:25.7 kN; A:21 mm; H:98 mm; SW:3.97 mm; Recommended tightening torque for set screw:8 Nm;

H2:62 mm; H:89 mm; A5:18.2 mm; Weight:1.33 kg; L3:65 mm; Recommended tightening torque for set screw:11.5 Nm; H1:80 mm; SW:4 mm; Designation of bearing:EX305G2T04; N2:36 mm;

G:M8x1; C0:20.8 kN; C1:6.5 mm; D:85 mm; d:45 mm; S:11 mm; m:6.5 mm; r:1.1; B:30.2 mm; B2:18.3 mm;

Clearance:C3; Reference Speed Rating (r/min):1200; SKU:24044ejw33c3-timken; Availability:In Stock; Cage Type:Steel; B:118mm; Limiting Speed Rating (r/min):1000; Seals or Shields:Open Type; D:340mm; Dynamic Load Rating (kN):1720;

Cage Type:Stamped Steel; B:76.203 mm; Da - Cup Frontface Backing Diameter:411.50 mm; Cup Part Number:129174; r - Cup Backface To Clear Radius2:4.83 mm; Aa - Cage-Cone Backface Clearance:14.2 mm; C1 - Dynamic Radial Rating (1 million revolutions)5:201000 lbf; Ab - Cage-Cone Frontface Clearance:-0.5 m

T max.:100 °C; A:57 mm; A2:82.5 mm; C:66 kN; s1:38.9 mm; T min.:-40 °C; L:160 mm; Designation of bearing:UC215G2T04; J:216 mm; C0:49.5 kN;

G:R1/8"; H2:41 mm; B:36.4 mm; T max.:100 °C; T min.:-20 °C; d:30 mm; L:274 mm; Designation of open end cover:SCOE206-30; Z:69 mm; d1:44.1 mm;

Ab - Cage-Cone Frontface Clearance:4.8 mm; Design Units:METRIC; C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)1:80500 lbf; R - Cone Backface To Clear Radius3:2.540 mm; B - Cone Width:33.000 mm; G1 - Heat Generation Factor (Roller-Raceway):98.4; da - Cone Frontface Backing Diameter:91 mm

Housing:SNT 507-606; Housing Mass:2.2 Kg; A1:52 mm; L:185.00 mm; N:15 mm; Seal:TA306; Shaft Diameter da:30 mm; Material :Cast Iron; N1:20.00 mm; A3:140 mm;

T1 - Bearing Width:1.8750 in; Cup Part Number:71750-B; a - Effective Center Location3:-0.26 in; D1 - Flange Outer Diameter:7.8080 in; R - Cone Backface To Clear Radius1:0.14 in; C90 - Dynamic Radial Rating (90 million revolutions)4:21200 lbf; C0 - Static Radial Rating:122000 lbf; Da - Cup Frontface

Diameter S-1:17 in; Housing Only2:SDAF3192K x 17; A:18.0000 in; D:5.7500 in; Stabilizing Ring 1 Reqd3:A8990; C:21.6250 in; F:15 in; Bolt Hole Length:3.375 in; Bolt Hole Width:2.5 in; B:54.2500 in;